Op-amp Adapters, Amp Interchangeable, Inverting/Noninverting/Cascaded/Filter Config, BNC/Banana Jack
Fabricated Using High Speed SiGe Process, Low noise Measurement/Controller Output
Con?gurable Gain, Precision & Rail-to-rail I/P, Very Wide/Over-the-top/Input Common Mode Ranges
Configured for Split-supply/Single-supply Operation, Easy Access to Pertinent Nodes with Test Points
Graphical user Interface Software for Board Control and Data Analysis, Various Power Supply
Selectable Vref, On-board Sense Resistor/External Resistor, Optional Input EMI/RFI Filtering
Convenient and Fast Verification of System Design, Provides Access to Inputs, Outputs, Gain Settings
Selectable Ref Voltage Options via Jumpers, Optional I/P EMI/RFI Filtering & O/P Isolation Resistor
16bit, High Accuracy Isolated Analogue Frond End(AFE), 0V-10Vin, Device Drivers, Pmod Compatible
Allows For Various Circuit Configurations, Through-hole Connector Provisions, RoHS Compliant
Evaluation of Difference Amplifier with very High Common Mode Voltage
Differential PECL Compatible Outputs, Robust Input Protection, Programmable Hysteresis
Digitally Controlled VGA, AC/DC Coupled Differential I/Os, SMA/USB Connector, Split/Single Supply
RF Performance Amplifier, Single-ended/Differential I/P, Differential O/P, Single/Split Supply, SMA
Edge-mounted SMA Connector, Enables Quick Breadboarding, User-defined Circuit Configuration
Easy Access to All Pins, Output Protection and Filtering Circuitry, LED indicator for Error Flag
High Speed & Precision Design, Includes Level Shifter & High-current Linearity Correction Section
Advanced Evaluation with Two Prototype Areas, Reference Voltage Source Flexibility
SPI Serial MMC/SD Card Interface, Bi-Directional Voltage Level Shifter
Adj Offset / Reference, Configurable for Dual or Single Supplies, Provision for Optional Circuitry
VCA with Passive CW Mixer, Integrates Time-gain-control, Imaging & Continuous Wave Doppler Paths
Ultrasound Transmit Solution, Includes Octal T/R Switch, High Voltage Pulser & Digital Beamformer
Non-inverting Amplifier Configuration, Easily Conversion to Inverting, SMA Connectors
User Adjustable Gain, Low Noise, High Speed
Logarithmic Detector for Measurement of Low Frequency Signal Power in Fibre Optic System
Two Package Variations Available: SOIC and MSOP, Solder Jumper, SMA/SMB Outline
USB Power and I/O, Small Form Factor, Simple Software Interface
Input Test Point, Potentiometer to Set Voltage, Push Button Switch to Initiate Calibration Sequence
Inputs Driven by Differential / Single Ended, Input Signals are Applied through SMA Jacks
Supported by IAR Development Tools & C Code Development, Isolated USB to UART Communication
Independent Shutdown Control for Each Channel, Internal Thermal & Short-circuit Protection
High Gain Amplifier, Integrated Band Pass Filter
High performance Roger's dielectric, Parallel or serial control, USB to SPI adapter
Adequate Area on PC Board Additional Circuitry, Separate Driver & Receiver Channel
Dual Non-Inverting Amplifier, 5MHz BW, 3V/us Slew Rate, Multiple Topology Config, 2.25-15V Supply
Non Inverting Dual Operational Amplifier, Configurable Topology, 5MHz BW, 3.8V/us Slew Rate, 36V Pwr
Differential Line Driver, Power Amplifier, 8.5MHz Bandwidth, 80V/us Slew Rate, 8V-20V Power
RTD Emulator Ckt Onboard, Supports Voltage and Current Output Mode, Post-Calibration Error of 0.1%
5V, 100mA Minimum Power Supply, and a Low Noise, Voltage Reference Supply for GAIN is Required
16bit, High Accuracy Isolated Analogue Frond End(AFE), 0.2V-4.096V I/P, Pmod Compatible
High Side Current Sense Amp, 2 Inverting Comparators, 400mV Reference, Reset Button, 2.7-60V Supply
1A Current Sense Amplifier, Jumper Selectable Current Limit, I2C, Pmod Compatible, 30V Supply
CML Compatible Output Stage, 1.25 ns Propagation Delay, Shutdown Pin
2mm, 2-terminal Screw Connectors,
Filter-Free Class-D Architecture, Flexible Operation With/Without I2C, Fast Start-up Time
2W Mono Bridged Output Drive, Ultra-low Shutdown Control, Tiny 8-pin MSOP PowerPAD Package
Integrated Digital Front-End (I2C), Piezo Actuator, Capacitive Touch Buttons, Programmable MSP430
High Accuracy, 16 Programmable Address, Power Supply of 2.7V to 5.5V
4-Quadrant Multiplication, 8-Lead SOIC & PDIP Packages
Multiple Feedback Lowpass Filter Stage, Dual Op-amp, Filter Wizard Evaluation, 4 Snap-apart Pack
Multiple Feedback Lowpass Filter Stage, Single Op-amp, Filter Wizard Evaluation, 4 Snap-apart Pack
Sallen Key Lowpass Filter Stage for Dual Op-amp, Filter Wizard Evaluation, 4 Snap-apart Package
4 Bi-Directional Level Translator, 1/2/4/8 Bit, Plugs Into Any Off the Shelf Prototype Board
Non Inverting Operational Amplifier, Configurable Topology, Rail-Rail Output, 5V Supply
Design & Eval of 6 Operational Amplifier, Low Voltage/Wide Supply Amplifier Series
Dual Op-amp in MSO8 Package, Can be configured as AC-coupled/Amplifier/Compensation/Filter Circuit
8 Lead MSOP Dual High Speed Operational Amplifier, Quick Breadboarding/Prototyping, Edge-mounted SMA
Unpopulated PCB for High Speed, Wide Bandwidth Op-amps, 8 Pin, SOIC Package
Universal Board is Suitable for Multiple Circuit Configurations, Single Op Amp in SOIC-8 Package
Dual Op-amp in SO8 Package, Can be configured as AC-coupled/Amplifier/Compensation/Filter Circuit
Reference Design Board to Demonstration for MCP6N11 Amplifier & MCP6V2x Wheatstone Bridge
24bit Weigh Scale w/ 16bit DAC, Ratiometric, User Programmable Offset/Gain/O/P Volt, 12V Supply
SOIC PowerPAD, 6W Stereo O/P Drive, TDA1517P Compatible, Mute & Standby Operation, Supply 9.5-18 V
Dual Current Sense Amplifier, 20V/V Gain Version, Real-Time Current Monitoring, 2.7-76V Input
DC Coupled, Low Noise, Gain Scaling 20dB/V, Single-ended Input & Differential Output
5/6 Lead SOT-23 High Speed Operational Amplifiers, Quick Breadboarding/Prototyping, Edge-mounted SMA
Easily Converted to Inverting Amplifier Configuration, 50ohm Input and Output for Easy Connection
Configured for Split Supply Operation, 50ohm Characteristic Impedance Trace, SMA Connectors
Internal Latch Pull-up Resistors, Power Supply Rejection Greater Than 70 dB
5/6 Lead SC70 High Speed Operational Amplifiers, Quick Breadboarding/Prototyping, Edge-mounted SMA
Current Sense Amplifier, Real-Time Current Monitoring, 100V/V Gain Version, -0.1V to 36V Input
Zero Drift INA, Level Shifting Output, Config Gains of 101V/V & 301V/V, Rail-to-Rail I/O, 5V Supply
Differential Latch Control, ESD Protection, Robust Input Protection, Typical Output Rise/Fall 165ps
PC Control with a GUI and USB Communications Board, RS232 Transceiver for UART Testing and Debug
Distance Measurement, LIN Master, RS-232 Transceivers & UART for Testing & Debug
Evaluation Board for the AMC1100 Single Channel Precision Isolation Amplifier
Evaluate the ADL5324 RF Driver Amplifier with SOT-89, 3 Lead Package
16bit, High Precision Analogue Frond End, 250KSPS, Device Drivers, ZedBoard Flatform, FMC Compatible
Configurable High Voltage Amplifier, 300kHz Bandwidth, -270 to 270V Input, 3.3V-50V Supply
Resistor Programmable Oscillator, 5KHz to 10MHz Frequency Range, SOT-23 Package
OIP3 of 48.5 dBm at 200MHz, Max Voltage Gain 26dB, -3dB Bandwidth of 1200MHz, Low Power Dissipation
210MHz Bandwidth, Low Distortion, High Slew Rate, High Voltage
300MHz Bandwidth, Low Distortion, High Slew Rate
1.8GHz Bandwidth, Unity Gain, High Slew Rate, Low Distortion
LMH High-speed Amplifier Family, 2.8GHz Bandwidth, Exceptional Signal Fidelity
Simple Gain Setting, Decoupled Supply Lines, 3 Generic, Easy to use PC Boards